Skip to main content

Free insulation estimate template

Insulation Estimate Template

The insulation estimates that go wrong are the ones that skipped the attic walk-through: vermiculite under the fiberglass, knob-and-tube wiring, a bath fan venting into the attic. This sample quotes an attic top-up and crawlspace job to stated R-values and writes those checks into the terms — so the customer knows why work would stop if one turns up.

By the Invoice Link team · Last updated

No sign-up. The Word file opens in Google Docs too: upload it to Google Drive, then choose Open with → Google Docs.

The filled-in sample

An attic and crawlspace estimate with air sealing, blown cellulose to a target R-value, baffles, hatch work and crawlspace batts, plus contaminated-insulation removal and bath fan ducts as options.

Thermal Line Insulation

Attics · Walls · Crawlspaces · Air sealing

604 Furnace St
Kingsfield, KY 40300
(859) 555-0166 · office@thermalline.example

Estimate

No.
EST-0412
Date
November 4, 2026
Valid until
December 4, 2026

Prepared for

Nolan and Ruth Whitaker

33 Sassafras Hill
Kingsfield, KY 40300
(859) 555-0153 · whitaker.home@example.com

Attic top-up (R-49 added) and crawlspace floor insulation

DescriptionAmount
Attic air sealing
Top plates, penetrations, chases, light boxes
1 job × $650.00
$650.00
Blown cellulose, R-49 added over the existing layer
1,400 sq ft × $1.70
$2,380.00
Rafter baffles at the eaves
30 ea × $6.50
$195.00
Insulate and weatherstrip attic hatch
1 ea × $125.00
$125.00
Crawlspace: R-19 batts between floor joists, supported
1,400 sq ft × $1.45
$2,030.00
Subtotal
$5,380.00
Estimate total
$5,380.00
Deposit to schedule (25%)
$1,345.00
Optional — priced separately, not included in the total
DescriptionAmount
Remove and dispose of rodent-contaminated insulation
About 300 sq ft near the eaves; billed by the area actually removed
300 sq ft × $1.25
$375.00
Extend bath fan ducts to the exterior
2 ea × $165.00
$330.00

Notes and terms

  • Before quoting, we checked the attic for vermiculite insulation and knob-and-tube wiring and found neither. If either turns up during the work, we stop until the right specialist has dealt with it.
  • Target levels follow ENERGY STAR's recommendations for climate zone 4A: add R-49 over the existing 3–4 inches in the attic, and R-19 under the floor. Final thickness, settled thickness and bag counts go on your installation record.
  • Existing recessed lights not rated for insulation contact get covers or a clearance dam.

How to pay: Deposit by card or bank transfer (ACH) through the pay link on your deposit invoice.

Customer signature — I accept this estimate and its terms

Date

Sample estimate — every name, address and price on it is fictional.Template from invoicelinkapp.com

Sample prices are illustrative, not a price guide. Replace them with your own rates.

How to estimate an insulation job

  • Measure the attic floor (and any wall or crawlspace areas) and note the existing insulation's type and depth.
  • Pick a target R-value from the climate zone and local code; the gap from the existing level sets how much to add.
  • Use the product's bag chart — coverage per bag at your target R-value — to count bags.
  • Plan the air sealing: top plates, penetrations, chases, recessed lights.
  • Check ventilation: baffles at the eaves, and bath fans that vent into the attic instead of outside.

Stop-work conditions to check before you quote

  • Vermiculite. EPA says to assume vermiculite insulation contains asbestos and not to disturb it, and to hire a professional asbestos contractor for work that would. Exclude it and refer the customer.
  • Knob-and-tube wiring. The National Electrical Code (394.12) doesn't allow concealed knob-and-tube wiring in hollow walls, ceilings or attics where loose, rolled or foamed-in insulation envelops the conductors; a few states, such as California, allow it under strict conditions. Have an electrician evaluate or replace it before you insulate.
  • Moisture, mold or roof leaks. Fix the source before insulating over it.
  • Recessed lights not rated for insulation contact. They need covers, clearance or replacement.

What to include in an insulation estimate

  • Target R-value and insulation type for each area.
  • Air-sealing scope and prep (baffles, dams, covers).
  • Removal of old insulation, if needed, priced separately.
  • Exclusions and the stop-work conditions above.
  • A promise of the FTC installation receipt when the job is done.

Before you send it

  • Areas measured; existing depth and type noted
  • Target R-value per area
  • Air sealing and ventilation plan
  • Vermiculite and knob-and-tube checks done
  • Removal priced separately if needed
  • Deposit and validity date

Insulation estimate questions

How do I figure how many bags of blown insulation I need?

Use the manufacturer's bag chart, which lists the coverage per bag and the installed thickness for each R-value. Divide the area by the coverage per bag at your target R-value and round up.

What if I find vermiculite in the attic?

Stop and exclude it. EPA advises treating vermiculite as if it contains asbestos and not disturbing it; refer the customer to a professional asbestos contractor.

Can I insulate over knob-and-tube wiring?

Not with loose, blown or rolled insulation surrounding concealed conductors — the National Electrical Code doesn't allow it, though a few states, such as California, allow it under strict conditions. Have an electrician evaluate or replace the wiring first, and note the condition on your estimate.

Should an insulation estimate promise energy savings?

Avoid a specific savings figure; results depend on the house and how it's used. Quote the work and the R-values, and show the recommendations you based them on.

What payment terms suit insulation work?

Attic jobs often finish in a day, so payment on completion is common; take a deposit on larger jobs that need materials ordered or a crew scheduled for several days.

Sources

Checked November 16, 2026. Prices and rules change — confirm with the source before you rely on them.

How we made this template

The sample business, customer, addresses and prices are fictional; they show how a insulation estimate is laid out, not what to charge. We used AI tools to help draft and check this page; every rule or standard it names, and every number that isn't sample math, links to its source. Spot something wrong? Email support@invoicelinkapp.com.

Skip the paperwork

Send this estimate from your phone — and get it signed

Invoice Link builds an estimate like this on your phone in a couple of minutes, then texts it to your customer with a link to approve it.

  • Texts estimates and invoices from your own phone number
  • On-site customer signatures on estimates; job photos on estimates and invoices
  • AI drafts estimates and invoices in English or Spanish
  • Card and bank-transfer (ACH) payments for US businesses
  • 10 contractor invoice designs

Free for 14 days

Every Pro feature, no invoice or estimate limit, no card needed. Then Pro is US$8.99/wk or US$94.99/yr (US prices; see pricing).

Start your free trial
Download on the App StoreGet it on Google Play

Just need a PDF? Use the free estimate maker.

Our mission

Every tradesperson deserves to get paid the day the job is done.