Skip to main content

Free hvac estimate template

HVAC Estimate Template

Replacement estimates are where HVAC jobs are won, and customers usually hold two or three of them side by side. The one that wins is rarely the cheapest; it's the one that shows how the system was sized, exactly what equipment goes in, and what happens if the ductwork turns out worse than it looks. This sample is a 3-ton heat pump replacement written that way.

By the Invoice Link team · Last updated

No sign-up. The Word file opens in Google Docs too: upload it to Google Drive, then choose Open with → Google Docs.

The filled-in sample

A heat pump replacement estimate with the equipment, line set and electrical itemized, a load calculation included at no charge, the permit passed through, and upgrades priced as options.

Blue Ember Heating & Air

Licensed mechanical contractor · Lic. #H-00000 · EPA 608 certified techs

915 Kiln Ave
Fernridge, SC 29600
(864) 555-0119 · service@blueember.example

Estimate

No.
EST-1192
Date
November 10, 2026
Valid until
December 10, 2026

Prepared for

Marcus and Joy Tillman

41 Briar Hill Rd
Fernridge, SC 29600
(864) 555-0131 · tillmans@example.com

Heat pump system replacement — 3-ton split system, attic air handler

Remove the existing heat pump and air handler and install a new matched 3-ton heat pump system, sized from a room-by-room load calculation, with a new line set, pad, disconnect and thermostat. Existing ductwork is reused after inspection.

DescriptionAmount
3-ton heat pump outdoor unit, R-454B
Matched system — the AHRI certificate number goes on the final invoice
1 ea × $3,450.00
$3,450.00
Matching variable-speed air handler with 8 kW heat strip
1 ea × $2,180.00
$2,180.00
New insulated refrigerant line set
1 set × $420.00
$420.00
Equipment pad, disconnect, whip and condensate safety switch
1 set × $310.00
$310.00
Heat pump thermostat, programmable
1 ea × $185.00
$185.00
Installation labor
Recover refrigerant and remove old equipment; set, braze, pressure test, evacuate, charge, start up and commission
1 job × $3,200.00
$3,200.00
Load calculation (ACCA Manual J) and duct inspection
Included
1 ea × $0.00
$0.00
Mechanical permit and inspection (passed through at cost)
1 ea × $135.00
$135.00
Subtotal
$9,880.00
Sales tax (example rate 7%)
$458.15
Estimate total
$10,338.15
Deposit to order equipment (25%)
$2,584.54
Optional — priced separately, not included in the total
DescriptionAmount
Upgrade to a variable-capacity heat pump
Higher efficiency rating; quieter at low speed
1 ea × $2,350.00
$2,350.00
Seal accessible duct joints and plenums
1 job × $650.00
$650.00
Extended labor warranty, 10 years
1 ea × $495.00
$495.00

Notes and terms

  • Sized from a room-by-room load calculation (ACCA Manual J), not from the old unit's tonnage. The report comes with this estimate.
  • If the duct inspection finds damage that would hurt the new system's performance, we'll price the repair in writing before installing.
  • Your price is locked when the deposit is paid, and we order the equipment then. Manufacturer parts warranty registration is included.
  • Payment schedule: 25% deposit to order equipment; balance at startup.

How to pay: Deposit by card or bank transfer (ACH) through the pay link on your deposit invoice.

Customer signature — I accept this estimate and its terms

Date

Sample estimate — every name, address and price on it is fictional, and the tax is an example: which lines are taxable depends on your state.Template from invoicelinkapp.com

Sample prices are illustrative, not a price guide. Replace them with your own rates.

How to estimate an HVAC replacement

  • Start with a load calculation. ACCA's Manual J is the ANSI-recognized procedure for calculating a home's heating and cooling loads, and ACCA's Manual S matches equipment to that load. Copying the old unit's tonnage carries forward whatever mistake was made last time.
  • Inspect ducts and returns. Undersized returns and leaky ducts limit any new system. Price their repair as required work or as options, and say which.
  • Check the electrical. Breaker and wire size against the new equipment's nameplate, and whether the disconnect and whip need replacing.
  • Confirm refrigerant and line set. New residential systems use lower-GWP refrigerants such as R-454B or R-32; decide whether the existing line set can be reused or must be replaced.
  • Get current equipment pricing from your distributor and put a validity date on the estimate.
  • Include the rest of the job: permit, startup and commissioning, refrigerant recovery from the old system and equipment disposal.

What to put on an HVAC estimate

  • Model numbers for each piece of matched equipment, plus their efficiency ratings (SEER2 and HSPF2, or AFUE for furnaces).
  • Whether the ductwork is reused, repaired or replaced.
  • Warranties: the maker's parts warranty (and who registers it), your labor warranty, and any extended labor coverage as an option.
  • Rebates only when you've confirmed the program and the equipment qualifies — and make clear who files for them.
  • A payment schedule: deposit to order equipment, balance at startup.

Good, better, best — as optional lines

Put your recommended system in the total and list upgrades on their own lines with their own prices: a variable-capacity system, duct sealing, an air cleaner, an extended labor warranty, a first-year maintenance plan.

The customer can approve one upgrade without asking you to rewrite the estimate, and the approved lines carry onto the invoice.

Before you send it

  • Load calculation done and attached
  • Equipment model numbers and efficiency ratings
  • Refrigerant type for the new system
  • Duct and electrical findings, with any required work priced
  • Permit, startup and disposal lines
  • Deposit, balance trigger and validity date

HVAC estimate questions

How do I size a system for an estimate?

Start with a load calculation — ACCA's Manual J is the ANSI-recognized method for calculating a home's heating and cooling loads, accounting for insulation, windows, orientation and air leakage — then choose equipment that matches it (ACCA Manual S). A tonnage copied from the old unit can repeat an old sizing mistake.

Should the estimate name the equipment brand and model?

Yes. Customers compare quotes by model, and naming it prevents the “they quoted a better unit” argument. If you might substitute an equivalent model because of availability, say so in your terms.

Can I still quote a new R-410A system?

Only in a narrow case: under EPA's Technology Transitions rule, a new residential split system using R-410A may be installed only if all of its specified components were made or imported before January 1, 2025. Repairs to existing R-410A systems are still allowed.

How big a deposit fits an HVAC replacement?

Enough to cover equipment you have to order, within your state's limits on home improvement deposits. Put the schedule on the estimate: deposit at signing, balance at startup.

Should I include maintenance in a replacement estimate?

Offer it as an optional line — a first-year maintenance plan with its own price. Customers who take it get a reminder visit before the next season, and you get the new system's first checkup.

Sources

Checked November 16, 2026. Prices and rules change — confirm with the source before you rely on them.

How we made this template

The sample business, customer, addresses and prices are fictional; they show how a hvac estimate is laid out, not what to charge. We used AI tools to help draft and check this page; every rule or standard it names, and every number that isn't sample math, links to its source. Spot something wrong? Email support@invoicelinkapp.com.

Skip the paperwork

Send this estimate from your phone — and get it signed

Invoice Link builds an estimate like this on your phone in a couple of minutes, then texts it to your customer with a link to approve it.

  • Texts estimates and invoices from your own phone number
  • On-site customer signatures on estimates; job photos on estimates and invoices
  • AI drafts estimates and invoices in English or Spanish
  • Card and bank-transfer (ACH) payments for US businesses
  • 10 contractor invoice designs

Free for 14 days

Every Pro feature, no invoice or estimate limit, no card needed. Then Pro is US$8.99/wk or US$94.99/yr (US prices; see pricing).

Start your free trial
Download on the App StoreGet it on Google Play

Just need a PDF? Use the free estimate maker.

Our mission

Every tradesperson deserves to get paid the day the job is done.