Skip to main content

Free plumbing estimate template

Plumbing Estimate Template

A plumbing estimate is where you win the job and where most disputes start. The customer compares your total with other quotes, the inspector expects the scope to match the permit, and anything you didn't write down becomes a conversation at the end. This sample is a filled-in whole-house repipe estimate, with the risky parts priced as unit prices instead of padding.

By the Invoice Link team · Last updated

No sign-up. The Word file opens in Google Docs too: upload it to Google Drive, then choose Open with → Google Docs.

The filled-in sample

A repipe estimate that separates materials from labor, turns hidden conditions into unit prices, and lists optional upgrades outside the total so the customer can add them without a new quote.

Ridgeback Plumbing & Drain

Licensed & insured · Lic. #P-00000

2210 Foundry St, Suite B
Wenzel Falls, WI 53500
(608) 555-0142 · billing@ridgeback.example

Estimate

No.
EST-1186
Date
November 10, 2026
Valid until
December 10, 2026

Prepared for

Ethan and Priya Marsh

77 Quarry Rd
Wenzel Falls, WI 53500
(608) 555-0129 · marsh.home@example.com

Whole-house repipe — PEX-A, single-story home with crawlspace

Replace the home's galvanized supply piping with PEX-A on a home-run manifold, from the main shut-off to every fixture. Work is done from the crawlspace with small access openings in walls where needed. Water will be off for part of two days.

DescriptionAmount
PEX-A pipe, fittings and hangers
1-inch main to the manifold; 1/2-inch home runs
1 lot × $1,480.00
$1,480.00
Home-run manifold, 14 ports, with isolation valves
1 ea × $395.00
$395.00
Repipe labor — 14 home runs plus the main
Home runs to the kitchen sink, 2 bath sinks, 2 tub/showers and the washer (hot and cold each) and 2 toilets; water heater and hose bibs fed from the main; pressure test; old lines capped and abandoned in place
1 job × $3,600.00
$3,600.00
New 1-inch main shut-off ball valve
1 ea × $145.00
$145.00
Wall access openings, cut clean and rough-patched
Up to 8 openings; finish patch and paint not included
8 ea × $45.00
$360.00
Permit and inspection (estimated, passed through at cost)
1 ea × $150.00
$150.00
Subtotal
$6,130.00
Sales tax (example rate 5.5%)
$111.10
Estimate total
$6,241.10
Deposit to schedule and buy materials (30%)
$1,872.33
Optional — priced separately, not included in the total
DescriptionAmount
Pressure-reducing valve
Recommended: the static pressure test during the walk-through read 92 psi
1 ea × $385.00
$385.00
Replace hose bibs with frost-free sillcocks
2 ea × $135.00
$270.00
Finish patch, texture and paint at each access opening
8 ea × $95.00
$760.00

Notes and terms

  • Price assumes clear crawlspace access. If we find conditions nobody could see — rotted joists, buried lines, earlier unpermitted work — we stop, show you, and price the change in writing before going on.
  • Unit prices if needed: openings beyond the 8 included, $45 each (unused openings credited); an added fixture connection, $150 each.
  • Not included: drywall finishing and paint (see optional lines), fixture replacement, water heater replacement, flooring or landscape repair.
  • Payment schedule: 30% deposit to schedule; balance due when the final inspection passes.
  • Pipe prices move with the market, so this estimate is good until the date above.

How to pay: Deposit by card or bank transfer (ACH) through the pay link on your deposit invoice.

Customer signature — I accept this estimate and its terms

Date

Sample estimate — every name, address and price on it is fictional, and the tax is an example: which lines are taxable depends on your state.Template from invoicelinkapp.com

Sample prices are illustrative, not a price guide. Replace them with your own rates.

How to estimate a plumbing job

Walk the job with a checklist. The numbers on the estimate are only as good as what you measured and tested on site.

  • Count fixtures and connections. Kitchen, baths, laundry, water heater, ice maker, hose bibs, gas appliances. Per-fixture counts are the backbone of repipe and rough-in pricing.
  • Check access. Crawlspace, basement, slab or second floor changes the labor more than the pipe does. Write the access you assumed into the estimate so the price is tied to it.
  • Test before you price. A static pressure reading and a look at the main shut-off, the water heater's age and its venting tell you which extras the job may need.
  • Price materials from a current quote. Pipe and fitting prices change. Use this week's supply-house pricing, not last year's spreadsheet.
  • Turn unknowns into unit prices. Instead of padding the total for hidden problems, list a unit price — “additional wall opening, $45 each” — that applies only if needed.
  • Add permit time and fees. Include the permit, the inspection visit and the re-inspection risk you're carrying.

What a plumbing estimate should spell out

  • Scope by fixture and material: PEX or copper, manifold or trunk-and-branch, and which fixtures get new connections.
  • Who restores walls and floors: access openings, patching and paint are the most common end-of-job surprise. Say who does what.
  • Exclusions: fixture replacement, water heater work, landscaping or flooring repair — anything a customer might assume is included.
  • How long the price holds: a validity date protects you from material swings and gives the customer a reason to decide.
  • Deposit and payment schedule: when money is due and what triggers the final payment — a passed inspection, not “done.”
  • How changes work: changes are priced in writing and approved before the work happens.

Offer options without writing three estimates

Optional lines priced outside the total let the customer upgrade without another visit:

  • A pressure-reducing valve or water treatment, only if your test shows it's needed.
  • Frost-free sillcocks, new stops at each fixture, or a recirculation pump.
  • Finished wall patching and paint at the access openings, for customers who don't want to hire a second trade.

When the customer approves an option, it moves onto the invoice as a regular line.

Before you send it

  • Fixture count and pipe material in the scope
  • Access assumptions written down (crawlspace, slab, finished ceilings)
  • Unit prices for anything you can't see yet
  • Permit and inspection line
  • Validity date and deposit terms
  • A signature line, or approval by link

Plumbing estimate questions

How long should a plumbing estimate be valid?

Long enough for the customer to compare quotes, short enough that material prices can't move far under you. This sample holds its price for 30 days; choose a period that matches how fast your supply prices change and print the date on the estimate.

How much deposit can a plumber ask for?

Whatever your written terms say, within your state's limits. California, for example, caps the down payment on a home improvement contract at $1,000 or 10 percent of the contract price, whichever is less. Check your state's contractor board before you set a deposit percentage.

Is a signed plumbing estimate a contract?

A signed estimate with a clear scope, price and terms generally works as the agreement for that work, but contract rules — and the wording some states require for home improvement contracts — vary. Have your standard terms reviewed once by someone who knows your state's rules.

What if I find something unexpected once the walls are open?

Stop, show the customer, and write a change order with the price before you continue. Unit prices on the estimate (extra openings, extra fixture connections) make this quick, because the customer already agreed to the rate.

Should the estimate show my hourly rate?

Only when you're pricing time and materials. On a fixed-price estimate, show task or phase prices; listing hours invites the customer to audit your speed.

Sources

Checked November 16, 2026. Prices and rules change — confirm with the source before you rely on them.

How we made this template

The sample business, customer, addresses and prices are fictional; they show how a plumbing estimate is laid out, not what to charge. We used AI tools to help draft and check this page; every rule or standard it names, and every number that isn't sample math, links to its source. Spot something wrong? Email support@invoicelinkapp.com.

Skip the paperwork

Send this estimate from your phone — and get it signed

Invoice Link builds an estimate like this on your phone in a couple of minutes, then texts it to your customer with a link to approve it.

  • Texts estimates and invoices from your own phone number
  • On-site customer signatures on estimates; job photos on estimates and invoices
  • AI drafts estimates and invoices in English or Spanish
  • Card and bank-transfer (ACH) payments for US businesses
  • 10 contractor invoice designs

Free for 14 days

Every Pro feature, no invoice or estimate limit, no card needed. Then Pro is US$8.99/wk or US$94.99/yr (US prices; see pricing).

Start your free trial
Download on the App StoreGet it on Google Play

Just need a PDF? Use the free estimate maker.

Our mission

Every tradesperson deserves to get paid the day the job is done.