Roofing · How-to
How to write a roofing estimate: measure in squares, list materials, price every line
A roofing estimate the customer can trust shows its math: the roof measured in squares of 100 square feet[1], a waste allowance of about 10–15%[1][2], every material and code-required item, and a price for each line. That includes the unknowns you can't see until the old shingles are off. HomeGuide puts an asphalt shingle roof at $3–$6 per square foot installed[3], and Fixr's average across roofing materials is $4.75[4]. Here's how to build an estimate line by line, with a worked example.
By the Invoice Link team · Reviewed · 8 sources
The short answer
Step 1: Measure the roof in squares
Roofers price in squares, and a square is 100 square feet of roof area[1]. Measure each roof plane (length along the eave × length up the slope), or measure the footprint including overhangs and multiply by the pitch multiplier below. For a first guess before you climb, start from the house's footprint (on a two-story house that's not the total living area), add the overhangs, and apply the multiplier.
| Pitch | Multiplier |
|---|---|
| 4/12 | Multiplier1.054 |
| 6/12 | Multiplier1.118 |
| 8/12 | Multiplier1.202 |
| 10/12 | Multiplier1.302 |
| 12/12 | Multiplier1.414 |
Multiply the flat footprint (overhangs included) by the multiplier to get the sloped roof area. Hips, valleys and dormers still need their own measurements.
Worked example
A simple gable roof
- Footprint with overhangs: 40 × 30 ft = 1,200 sq ft
- Pitch 6/12: 1,200 × 1.118 = 1,342 sq ft of roof
- Squares: 1,342 ÷ 100 = 13.4 squares
13.4 squares. We'll price this roof through the steps below.
Step 2: List the materials, with waste
Owens Corning says to add 10%–15% to all your material totals for the trim allowance, the waste factor[2]; IKO gives the same general range and notes smaller roofs tend to waste a higher share than larger ones[1]. Use the high end for cut-up roofs with hips, valleys and dormers.
- Shingles. Laminated lines like IKO Cambridge come 3 bundles to the square, 33.3 square feet a bundle[1]. Owens Corning's Duration is also 3 bundles a square, but covers 98.4 square feet[5], so round up.
- Underlayment. Synthetic underlayment comes in 10-square rolls and #15 felt in 4-square rolls[2]; IKO's StormTite synthetic is a 1,000-square-foot roll[1]. Add waste here too[2].
- Ice barrier along the eaves where your code requires it (Step 3), and in valleys if you use it there.
- Drip edge in linear feet: the total length of eaves plus rakes.
- Starter strip, hip and ridge cap, flashing, vents, nails and sealant, each as a quantity, not "misc."
Step 3: Put the code items on the estimate
Code requirements are cost, and an estimate that leaves them off either loses you money or loses you the job to someone who reads the code to the homeowner. The International Residential Code is in use or adopted in 49 states, the District of Columbia and several territories[6]. From its 2021 edition[7]:
- Ice barrier (R905.1.2). Required where there's a history of ice forming along the eaves, as the local climate table designates. It runs from the lowest edges of all roof surfaces to at least 24 inches inside the exterior wall line, and on roofs of 8:12 or steeper also at least 36 inches up the slope from the eave edge[7].
- Drip edge (R905.2.8.5). Required at eaves and rake edges of shingle roofs, overlapped at least 2 inches, extending at least 1/4 inch below the sheathing and 2 inches back onto the deck, fastened no more than 12 inches apart[7].
- Low slopes (R905.2.2). Asphalt shingles only on slopes of 2:12 or more, with double underlayment from 2:12 up to 4:12[7].
- Overlays (R908.3.1.1). No recover over a roof that's water-soaked or too deteriorated to serve as a base, that's slate, clay, cement or asbestos-cement tile, or that already has two or more layers[7]. A replacement removes the old roof down to the deck (an adhered ice barrier membrane may stay)[7].
Check your local edition
States and cities adopt the IRC in different editions and with amendments. These are the 2021 model code sections; your building department's adopted version is the one that counts, and the permit office will tell you which it is.
Step 4: Price each line
| Line | Published price | Source's date |
|---|---|---|
| Tear-off and disposal | Published priceAbout $50 a square including dumping, up to $150 for heavy materials or multiple layers (Fixr)[4]; $100–$300 a square (HomeGuide)[3] | Source's dateFeb 4, 2026 · Nov 7, 2025 |
| Materials | Published price$100–$250 a square (HomeGuide)[3] | Source's dateNov 7, 2025 |
| Labor | Published price$150–$300 a square in HomeGuide's text, $200–$350 in its calculator[3]; 40%–60% of the total (Fixr)[4] | Source's dateNov 7, 2025 · Feb 4, 2026 |
| Ice and water shield | Published priceAbout $0.50 a sq ft, roughly $50 a square (Fixr)[4] | Source's dateFeb 4, 2026 |
| Decking replacement | Published price$2–$5 a sq ft installed (HomeGuide)[3]; $2–$8 (Fixr)[4] | Source's dateNov 7, 2025 · Feb 4, 2026 |
| Permit | Published price$100–$500 (HomeGuide, Fixr)[3][4] | Source's dateNov 7, 2025 · Feb 4, 2026 |
| Whole job, installed | Published price$400–$900 a square with tear-off, or $3–$6 a sq ft for asphalt shingles (HomeGuide)[3]; $3.75–$11 a sq ft across materials, $4.75 average (Fixr)[4] | Source's dateNov 7, 2025 · Feb 4, 2026 |
Use your supplier's prices and your own crew's production, and these ranges as a check.
Worked example
Pricing the gable roof (example unit prices inside the published ranges)
- Tear-off, one layer: 13.4 squares × $100 = $1,340
- Shingles, underlayment and accessories: 15 squares × $200 = $3,000
- Labor: 13.4 squares × $250 = $3,350
- Ice barrier along 80 ft of eaves: 3 squares × $50 = $150
- Permit (example): $200
- Total: $8,040, about $600 a square or $5.99 a square foot of roof
- Decking, if needed: $4 a sq ft installed, $128 a 4 × 8 sheet, billed only for sheets replaced
$600 a square sits inside HomeGuide's $400–$900 with tear-off, and $5.99 a square foot inside its $3–$6 for asphalt shingles.
For your own labor rate, start from your real costs. For comparison, the median employee roofer earned $55,440 a year, or $26.65 an hour, in May 2025[8]; your rate also has to cover insurance, equipment, disposal and the hours spent estimating. The labor cost calculator and markup calculator help with both.
Step 5: Write the unknowns down
Many roofing disputes come from things nobody could see on estimate day. Price them up front as unit prices or allowances, so the change is arithmetic, not an argument:
- Rotten decking: a price per sheet, plus how you'll tell the customer (photos before you replace).
- Extra layers: a price per square for each additional layer found.
- Damaged flashing, fascia or rafters: an hourly rate or a quote before work starts.
- Weather: what happens to the schedule, and who pays for tarping overnight.
- Warranty: the manufacturer's shingle warranty and your workmanship warranty, as separate lines.
- Cleanup: magnet sweep, dumpster placement and driveway protection.
Step 6: Send it, get it signed, collect the deposit
The roofing estimate template shows a filled-in replacement estimate with these lines, and the roofing invoice template the final bill with the deposit credited. For what deposit to ask for (some states cap it), see how much deposit a contractor should ask for.
Invoice Link pulls the house's square footage from public records on the customer's profile, which gives you a first look at the house's size before you climb; attaches your roof photos to the estimate; gets it signed on your phone; and sends a link for the deposit. When the job's done, the estimate becomes the invoice in one tap.
Before you send the roofing estimate
- Roof measured in squares, pitch included
- Waste of 10–15% on every material
- Ice barrier and drip edge per your local code
- Layers checked: overlay allowed or not
- Decking and extra layers priced as unit prices
- Permit fee from the building department
- Warranty and cleanup written out
- Deposit and payment schedule stated
Questions contractors ask
How do you calculate roofing squares?
A roofing square is 100 square feet of roof area. Measure each roof plane, or multiply the footprint including overhangs by the pitch multiplier (1.118 for a 6/12 roof), then divide by 100. A 1,200 square foot footprint at 6/12 is about 13.4 squares.
How much waste should I add to a roofing estimate?
IKO and Owens Corning both use about 10 to 15 percent. Owens Corning says to add it to all material totals; use the high end on roofs with hips, valleys and dormers, and remember smaller roofs tend to waste a higher share.
What should a roofing estimate include?
The measured squares, every material with quantities, tear-off and disposal, labor, code items like ice barrier and drip edge, the permit, unit prices for rotten decking and extra layers, the warranty, cleanup, the deposit and the payment schedule.
How much do roofers charge per square?
HomeGuide puts roofing labor at $150 to $300 a square and a whole replacement at $300 to $600 a square installed, or $400 to $900 including tear-off. Fixr says labor is 40% to 60% of the total.
Can you install a new roof over the old one?
Under the 2021 International Residential Code, not if the existing roof is water-soaked or too deteriorated to serve as a base, is slate, clay, cement or asbestos-cement tile, or already has two or more layers. Your local code edition may differ, so check with the building department.
Is ice and water shield required?
The 2021 International Residential Code requires an ice barrier where there's a history of ice forming along the eaves, extending from the eave edge to at least 24 inches inside the exterior wall line, and on roofs of 8:12 or steeper at least 36 inches up the slope. Whether your area is one of them is set in the local code.
Sources
Every figure above links here. We checked each source on November 16, 2026; the date after each one is the source's own (its data period or its last update). Prices and rules change, so confirm with the source before you rely on a number.
- [1]IKO: How Many Square Feet in a Bundle of ShinglesPublished July 19, 2023; page modified February 25, 2026
- [2]Owens Corning: DIY Roofing: Re-Roofing TipsPublished October 11, 2023
- [3]HomeGuide: How Much Does a Roof Replacement Cost? (2026)Dated November 7, 2025
- [4]Fixr: How Much Does a Roof Replacement Cost in 2026?Updated February 4, 2026
- [5]Owens Corning: TruDefinition Duration ShinglesProduct page (no date shown); read November 16, 2026
- [6]International Code Council: The International Residential CodeNo date shown; read November 16, 2026
- [7]International Code Council code text, via UpCodes: 2021 International Residential Code, Chapter 9: Roof Assemblies (as adopted without amendments by Colorado's Division of Fire Prevention and Control)2021 edition; read November 16, 2026
- [8]U.S. Bureau of Labor Statistics: Roofers (Occupational Outlook Handbook)May 2025 wage data; page last modified September 14, 2026
How we made this guide
Every number on this page comes from a public source listed above: government data, building codes, manufacturers' published specs, or homeowner cost guides that publish what jobs cost. Cost guides survey different jobs in different places, so we show their ranges side by side with each publisher's own date instead of averaging them into a number of our own. Worked examples are labeled as examples, and their inputs are either cited or plainly made up for the math. We used AI tools to help research and draft this guide, and every figure was checked against its source in a separate fact-check pass before it was published. We didn't pay anyone quoted here, and there are no testimonials. Spot something wrong or out of date? Email support@invoicelinkapp.com.
Skip the paperwork
Send the roofing estimate from the driveway
Invoice Link builds the estimate with your line items and roof photos, gets it signed on the spot, and collects the deposit through a pay link.
- Texts estimates and invoices from your own phone number
- On-site customer signatures on estimates; job photos on estimates and invoices
- AI drafts estimates and invoices in English or Spanish
- Card and bank-transfer (ACH) payments for US businesses
- 10 contractor invoice designs
Free for 14 days
Every Pro feature, no invoice or estimate limit, no card needed. Then Pro is US$8.99/wk or US$94.99/yr (US prices; see pricing).
Start your free trialJust need a PDF? Use the free estimate maker.
Keep going
More guides
Free tools